Search Results

An earlier paper by Blair and Cahoon (SAE 710082) described the initial design and development of a 60 hp engine of the single-cylinder 2-cycle type for road racing motorcycle applications. This paper continues with the further design of this engine as a 65 hp 5-speed transmission unit and a variation of it as a 40 hp 4-speed transmission engine for moto-cross racing usage. A discussion of the application of the computer to the design of both engines is included. The computer design is used for the prediction of the required torque/speed characteristics for both engines for their particular application in order to eliminate lengthy test bed development. The mechanical design criteria for the engine/transmission units are also discussed and their implementation for the road race or moto-cross application described.

This paper describes a theoretical and experimental investigation of the noise characteristics of some basic internal combustion engine exhaust systems. On the basis of a one-dimensional analysis of the unsteady internal flow, the treatment is extended to consider the noise radiated by the efflux of gas from the atmospheric termination of the tail pipe. Using a rotary valve exhaust simulator, experimental pressure-time histories and one-third octave noise spectrograms were obtained. These are compared with those calculated.

This paper describes a unique and uncomplicated method of stratified-charging a two-stroke cycle engine which assists in reducing the short-circuited loss of fuel during scavenging. Performance characteristics as presented were acquired from tests conducted on a 400 cm3 naturally aspirated, single cylinder, spark ignition two-stroke engine with carburettor control of gasoline fuel, the design and construction of the engine also being done at The Queen's University of Belfast. Using a tuned exhaust pipe, the engine produces a peak power of 16 kW at 5000 rev/min and has a minimum brake specific fuel consumption of 0.275 kg/kWh. Moreover, for the tests presented at full and quarter throttle openings, virtually all of the brake specific fuel consumption values are below 0.36 kg/kWh. Most of the performance characteristics shown at various engine speeds are as a function of air/fuel ratio. This paper is a continuation of that presented as SAE 830093.

A three cylinder two-stroke cycle diesel engine is proposed for automotive use. The engine is of the simple loop or cross-scavenging type with a crosshead seal and under piston scavenging pump. This paper records the initial investigations of this concept using a purpose built single cylinder engine. Results from different combustion systems are presented together with tests with the same engine when using an external air supply. Measurements from a parallel investigation using a laser doppler anemometer to measure air swirl motion within one of the chambers are also presented.

The paper discusses the application of maps of measured discharge coefficients for poppet valves, cylinder ports, and in-pipe throttles within a theoretical simulation of the unsteady gas flow through an internal combustion engine. The maps provided cover both inflow and outflow at the discontinuity being discussed and are displayed as contour maps of the discharge coefficient as some function of the geometrical flow area of that discontinuity and of the pressure ratio across it up to a maximum value of 2.0. An engine simulation package is used for both a four-stroke and a two-stroke engine to determine the typical pressure ratio and area ratio characteristics which pertain at all such discontinuities at representative engine speed and load conditions.

The application of in-cylinder multi-dimensional modelling to the scavenging process within the cylinder of a two-stroke cycle engine requires a prior knowledge of the flow entering that cylinder. Without this information, assumptions must be made which limit the accuracy of the theoretical simulation. This paper describes laser doppler anemometry measurements of transfer port efflux flow for a two-port loop scavenged test cylinder motored at 200 rev/min. The cylinder was externally blown to ensure scavenge flow into the cylinder over the entire transfer port open period. The test results indicate that the flow does not enter the cylinder in the port design direction, but varies as a function of port height during both port opening and closing. Comparison of motoring results with those obtained under steady flow testing of the same cylinder, shows adequate correlation, thereby justifying the use of steady flow information for dynamic simulation.

From a theoretical analysis of the unsteady efflux from the open end of a simulated reciprocating internal combustion engine exhaust system a prediction of overall and one-third octave sound pressure levels in space, due to this gas flow, is produced. The predictions are compared with measured levels and show a high degree of correlation.

In two previous papers to this Society (1, 2)* an ‘alternative’ method was presented for the prediction of the unsteady gas flow behaviour through a reciprocating internal combustion engine. The computational procedures led further to the prediction of the overall performance characteristics of the power unit, be it operating on a two- or a four-stroke cycle. Correlation with measurements was given to illustrate its effectiveness and accuracy. In the ducts of such engines there are inevitably sectional changes of area which are either gradual or sudden. A tapered pipe is typical of a gradual area change whereas a throttle or a turbocharger nozzle represents a sudden area change. In those previous papers it was indicated that a fuller explanation, of the theoretical procedures required to predict accurately the unsteady gas flow in such duct sections would be given in a later paper to this Society; this is that necessary publication.

This paper describes some of the experimental and theoretical work carried out at the Queen's University, Belfast in connection with a pulsejet project. It starts from the earliest stages of trying to achieve a working reed valved engine and continues to the present where valve less pulsejets have been designed with the aid of a simulation program. Suggestions are made regarding the manner in which various parameters such as duct and intake geometry, orientation and flight speed can affect performance. It suggests four main criteria which must be fulfilled for any valveless pulsejet to operate successfully and discusses methods by which these can be achieved.

Earlier papers by the principal author in conjunction with others have described the prediction of noise and performance characteristics of two-cycle spark-ignition crankcase compression engines. These calculations are performed on a digital computer and are shown to simulate accurately the unsteady gas flow and thermodynamic processes in such power units. The engines described previously had induction control by the piston or with a disc valve. In this paper the work is extended to engines fitted with reed valves controlling intake air flow and examples illustrating the effectiveness of such calculations are presented. In particular, a single-cylinder industrial engine is employed to show clearly the effects of changing such parameters as reed petal thickness, stop-plate radii and numbers of reed petals on the performance characteristics.

Previous papers published by the author have described unsteady gas flow through a naturally aspirated two-cycle engine and the most recent of these publications details a theoretical modelling of the gas exchange or scavenge process for the cylinder of this type of power unit. This results in the ability to predict the trapped charge state, mass, and purity characteristics. With such information it becomes sensible to apply a closed cycle thermodynamic analysis to it and to further predict directly power, torque, and fuel consumption characteristics. This paper describes such a simple closed cycle analysis and compares the theoretical results of power, mean effective pressure, specific fuel consumption, and cylinder pressure diagrams with corresponding measured data from two engines.

At the 1999 SETC meeting, a paper presented a simple, tuned and silenced exhaust system for a two-stroke engine which theoretically reduced both noise and exhaust emissions and increased engine power and fuel efficiency. In this paper that design concept is applied to a small 56 cc industrial engine and experimentally shown to deliver the projected behaviour which was predicted in that earlier publication. Experimental test results are presented for power output, fuel consumption, and exhaust emissions to illustrate these statements. An accurate engine simulation software package (VIRTUAL 2-STROKE) is employed to model the entire two-stroke engine and to demonstrate not only its effectiveness as a design tool in this area but also that it can accurately predict the above-mentioned performance and emission characteristics.

An experimental and theoretical investigation to minimise the hydrocarbon emissions from a 25 cm3 two-stroke engine with finger transfer ports is described. Finger ports have the side of each passage closest to the cylinder axis open to the cylinder bore making it possible to produce high-pressure die castings with the simplest of dies. Cylinders utilising this type of porting are believed to have inferior scavenging characteristics compared to those using closed or cup-handle porting. The effects of cylinder scavenging characteristics and port optimisation on engine performance were examined using a computer simulation. It is concluded that there is potential for a 70% reduction in exhaust hydrocarbon emissions through scavenging efficiency improvements and port optimisation, provided the cylinder scavenging can be developed to match that of the best existing unconventional crossflow scavenged designs.

The emissions produced from a simple carburetted crankcase scavenged two-stroke cycle engine primarily arise due to losses of fresh charge from the exhaust port during the scavenging process. These losses lead to inferior fuel consumption and a negative impact on the environment. Pressure on exhaust emissions and fuel consumption has reduced the number of applications of the two-stroke cycle engine over the years, however the attributes of simplicity, high power density and potential low manufacturing costs have ensured its continuing use for mopeds and motorcycles, small outboard engines and small utility engines. Even these last bastions of the simple two-stroke engine are being challenged by the four stroke alternative as emissions legislation becomes tighter and is newly formulated for many categories of engines. A simple solution is described which reduces short circuit and scavenge losses in a cost effective way.

The paper describes and lists the performance characteristics of a 400 cm3 single-cylinder two-stroke cycle engine with natural-aspiration, spark-ignition and carburetter control of gasoline fuel. The engine features an uncomplicated and unique system of stratified-charging which helps reduce the short-circuited loss of fuel during scavenging. With an untuned exhaust system the engine produces a peak power of 13 kW at 5500 rev/min and a brake specific fuel consumption which has a minimum of 0.265 kg/kWh but, more importantly, virtually the entire speed and load range is below 0.34 kg/kWh (0.55 lb/hp. hr). All performance characteristics at several throttle openings are presented at various engine speeds as a function of air/fuel ratio.

Engine cycle simulation is an essential tool in the development of modern internal combustion engines. As engines evolve to meet tougher environmental and consumer demands, so must the analysis tools that the engineer employs. This paper reviews the application of such a tool, VIRTUAL 4-STROKE [1], in the modelling of a benchmark 1.9 Litre TDI engine. In an earlier paper presented to the Society [2] the authors presented results of a validation study on the same engine under full load operation. This paper expands on that work with validation of the simulation model against measured data over a full range of part load operation.

This paper presents a single-cycle gas simulation of the scavenging process in a two-stroke cycle engine. The apparatus used is described in the most detailed fashion and the experimental procedure is covered completely. On the apparatus is placed some eleven differing cylinders of a Yamaha 250 motorcycle engine and the scavenging efficiency - scavenge ratio characteristics of each determined experimentally. The results of these experiments are compared with the known performance characteristics of the same eleven cylinders which were obtained under firing conditions for variations of power, torque, air-flow, fuel consumption and scavenging efficiency at several speeds and throttle positions. The correlation, between the ranking of the several cylinders determined on the scavenging simulation apparatus with the performance characteristics obtained under firing conditions, is very good.

A computer program has been developed which predicts the sound pressure level and the frequency spectrum produced by simple engine exhaust systems. The program utilizes unsteady flow gas dynamic theory to predict the pressure-time history in the exhaust system and the velocity-time history at the open end of the system. Acoustic theory is then used to predict the sound pressure levels and frequency spectrum in free space. The work was carried out on a twin-cylinder four-cycle engine, but the theory can be applied to any internal combustion engine.

The study of scavenge flow in two-cycle engines is of great importance in the development of that type of internal combustion engine and has been extensively covered by numerous researchers over the last half -century. Alfred Jante in SAE paper 680468 suggested an indirect and comparative test for the assessment of scavenge flow which he, and others, have shown to be both a simple and extremely relevant technique. The acquisition and reduction of data for this experimental method proved to be laborious and time consuming, and it is the purpose of this paper to show that it is possible to eliminate these tedious aspects by automation of both data recording and processing. This is described and examples of its usage are given.

Modern turbocharged diesel engines employ exhaust driven turboblowers operating at high speeds up to 100,000 rpm. The performance assessment of such units demands precise and controllable power absorption and torque measurements at these very high rotational speeds. Additionally the parameters, speed, mass flow, static and dynamic pressures and temperatures must be measured. The turbine power absorption and torque measutement present unique problems. The remaining parameters may present some difficulties but generally the problems are not so great. The design of a high speed dynamometer and the development problems encountered are described. The dynamometer has been used to establihs the performance characteristics of a C. A. V. 01 turbocharger and these are reported.